• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up a doorway Up a Door

boarding up houses emergency boarding up 24/7 a door is one method of protecting vacant investment properties from the elements. While it won't prevent all damage, it can avoid certain problems caused by severe storms.

The idea of boarding up doors and windows can deter trespassers or vandals from entering your property. Placing plywood boards over doors and windows can be costly and time-consuming.

Measure the Door

The first thing you'll need is a tape measure. You may want to keep a ladder or a chair close by in case you require a better view of the top of the frame. Wear gloves and protective glasses when you make use of these tools.

Start by taking measurements of the length of the door. You can do this by running a tape measure horizontally along the door. Be sure to take out all extra parts of the door, such as the sweep, when measuring. Next, measure the height by measuring up from the floor to the current sill plate or the lintel. It is essential to measure more than one location especially for older doors, because they are not always a perfect rectangle. If the measurements are different then use the largest figure.

After you've logged the width and height measurements, you'll need to figure out what size boarding up commercial property you'll need to fit into the frame. It should be at least 2 inches larger and 1'' taller than the door. 2'' higher. This will give you plenty of space to move the frame and door into place.

When you're ready to measure the door frame's width and height measurements It's a good idea to remove any trim or casing the door jambs, so you can see the studs behind them. This will help you to determine the exact measurement of the space between the studs and the edges of the frame.

After you've removed your trim, you can determine the size of the frame of your door by running the tape over the entire frame in three locations and using the smallest measurement to determine your door's width. It is also important to take measurements of the frame's height from top to bottom, on both sides. Use the shortest measurement for the width of your door.

If you are having trouble with the measurements, you should consult a professional to come to your home and take the measurements. They will tell you what size and style of door you need and how to prepare your frame for a replacement door.

Cut the Plywood

A door frame is typically made of a series of studs or thin boards that create an open space around the door. The typical door is secured by two hinges that are fixed to the studs. This means that if you need to refinish the door, it is necessary to remove the hinges from the door for a night. To stop insects from entering your home and to secure the door's opening, a simple method of boarding up property doors is to place plywood in the opening. It's easy to do this without nailing or screw the plywood onto the frame of the door.

Plywood is cheap, easy to work with and looks stunning when finished. This makes it the perfect material to provide temporary solutions to problems that require the removal of an existing door while refinishing or installing a new one. It can also be used to protect the opening of a room being renovated, like a basement or construction site.

For a wall constructed of plywood begin by taking measurements of the width and height of the door opening. Mark the measurements with a utility blade and a straight edge made of metal like a drywall or a metal square. Then, draw a chalk line across all the lines you have marked to mark the areas you want to cut. Utilize a circular blade to cut the plywood to the desired size.

When cutting the plywood it is crucial to shield your ears and eyes. If possible wear eye protection and earplugs as you are working. It is also important to use a blade with a lot of teeth, which will permit you to cut quickly and with minimal tear-out. To minimize the chance of cutting pieces of wood from the edges of the cut, use a small block of wood as template to guide the blade and keep it at a distance of just a hair's width away from the mark when cutting.

An effective way to hold the plywood in place without screwing it to the studs is by fixing braces that are short at each end. Place one brace on the side that is inside and the other one on the outside of the door. Then, boarding up doors place a pair of 1-1/2-inch deck screws into each of the holes, and tighten them using an open-end wrench.

Fasten the Plywood

It's time to attach the panel to the frame after you have the plywood sheet cut to the right dimensions and the holes for the stiles and rails of the door frame predrilled. This is a straightforward project that doesn't require any advanced carpentry skills, as long as you have the right tools and follow the correct steps.

Begin by setting up a worktable near the doorway, with two sawhorses and 2-by-4 framing lumber at each end of the table. Lay the full sheet of plywood flat on top the sawhorses using the marks left by the measurement process as a guide to cut. Mark the lines using the help of a utility knife, a drywall square or any other metal straight edge. This will serve as a guide for the saw blade and keep the wood from splintering when cutting the plywood.

Put on eye protection and cut along the scored lines using a circular or table saw fitted with a fine-tooth blade. Sand the edges of the panels with 120-grit paper to smooth it out and remove any burrs. After the sanding, apply a layer of wood sealer on the plywood panels and allow to dry as directed by the manufacturer.

Install the hinges on the frame of the door. If you're using T hinges, make holes through the exterior of the door for the straps of the hinges. Then, screw the outside hinge to the frame with a screwdriver. Repeat the same procedure on the inside of the door for each of the hinges remaining, being careful not to overtighten any of them, or the door will shift.

If you're using one outside hinged door you can make it easier to lock and close using a chain latch by putting a piece of wire through the loops of the hinges outside. Bend a short piece of tie wire in half, and place it through the two holes on the outside of the door. You can then connect the wires to tighten them and lock the door.

Install the Plywood

Place the plywood in the door's opening using the measurements that you have taken. Move the header (top) of the frame and the sill (bottom). Use a level and make sure that there is no slop between the sill and header. If it's not perfect you can place a second shim wherever necessary and continue the process until the header and sill are plumb.

Once the plywood is inside the frame, fasten it with stainless steel hinge bolts and wings nuts. It's a good idea utilize a screw gun that has an hex-head attachment so that you avoid stripping the head of the screws.

If your home has studs that run along the length of your doorway, you could drill hanger bolts into every framing piece. This is a simpler task than drilling the hole with a drill or drywall saw.

After installing the plywood determine the width and height of the door opening. If necessary, trim your plywood bottom to match the height the door frame. Cut two pieces of framing lumber 1 by 6 to serve as braces for the upper and lower ends. Cut along the lines marked on your plywood using circular blades with teeth that are finely tipped. Wear eye protection. Splinters can be removed from cuts using a sanding tool.

After you've put in the braces after you have positioned them, use two pairs of 2-inch finishing nail to attach each brace to the plywood. When you're finished counter-sink the heads of all the nails. Make sure to seal the braces and the plywood with a quality wood sealer, like this wipe-on polyurethane by Minwax.

If the door is too large, you can either add decorative molding to fill the space between your door and jamb, or you can reduce the size of your opening. In many situations, it's more affordable and simpler to just get an alternative door. It also solves any issues you might have encountered with the door you originally purchased, if it was damaged or was not fit for the opening.